Incoloy 800 Pipe Fittings Supplier

Alloy 800 Pipe Fitings, ASTM B366 UNS N08800 Buttweld Fittings, Inconel WPNIC Seamless Pipe Fitting, Inconel 800H Pipe Fittings Manufacturer in India

Inconel 800 Pipe Fittings Suppliers in India

We as a Metalfed Engineering is an eminent supplier and exporter of Incoloy 800 Pipe Fittings, which are typically used in high temperature applications. Alloy 800 Buttweld Fittings does not yield to general oxidation or pressure corrosion cracking produced by chloride ions, smooth in extreme temperature circumstances. These factors factors make Inconel Alloy UNS N08800 Pipe Fittings ideal alloys for applications from hot section gas turbines to deep sea well drilling. It is used as wire rope for mooring cables, propeller blades for motor patrol gunboats, submarine auxiliary propulsion motors, etc. Though exact measurements vary, reported statistics state the range of the Inconel Alloy WNR 1.4876 Pipe Fittings melting point between 2,350 Degree F and 2,460 Degree F (1,290 Degree C and 1,350 Degree C).

During powder bed fusion or directed energy deposition of Inconel 800 End Cap Pipe Fittings, dendrites form along the build direction, which is the direction of the highest temperature gradient during deposition, and elongated grains form in this direction as well. Alloy 800 Dish Cap Pipe Fittings is known for its ability to withstand incredibly high temperatures. At such high temperatures in the presence of oxidising agents, the titanium and niobium compositions of the oxide film on Inconel Alloy 800 Cross Pipe Fittings increase drastically to form a natural protective layer in the material.

Exporter of Incoloy 800HT Welded Pipe Fittings, ANSI B16.9 Incoloy 800 Butt weld Fittings, 800 Incoloy® Equal Tee Fittings, WERKSTOFF NR. 1.4876 Pipe Cap, ASME SB 366 Incoloy Alloy 800 Pipe Bend, Nickel Alloy 800 Stub End.

Table of Content

Incoloy 800 Pipe Fittings Specifications
Incoloy Alloy 800 Fittings Equivalent Grades
Incoloy 800 Pipe Fittings Chemical Composition
Alloy 800 Pipe Fittings Mechanical Properties
Inconel 800 Pipe Fittings Size Range
Incoloy 800 Pipe Fittings Manufacturing Standards

Incoloy 800 Pipe Fittings Dimensional Tolerances
Incoloy Alloy 800 Pipe Fittings Dimensions
ASTM B366 UNS N08800 Pipe Fittings Applications
Inconel Alloy 800 Pipe Fittings Exports to
Nickel Alloy 800H Pipe Fittings Types and Prices

Incoloy 800 Buttweld Elbow is a completely austenitic advanced corrosion-resistant blend that offers resistance to together aqueous corrosion then attack at elevated fevers.We also have largest stock of Inconel 600 Pipe Fittings, Incoloy 825 Pipe Fittings, andInconel 625 Pipe Fittings at best price.

Value Added Services

Epoxy Coating
Electro Polish
Sand Blasting

Testing

Intergranular Corrosion Test
Tensile Test
Hardness Test

Features

Good load bearing capacity
Excellent versatility and weldability
High tensile strength

Stockholder of Incoloy Alloy 800 Two Joint Pipe Fittings, DIN 1.4958, 1.4859 Cross Fittings, Incoloy Alloy 800H Buttweld Elbow, Alloy 800 Reducer, Incoloy Alloy 800HT Equal Tee at best price in India.

Incoloy Alloy 800/800H/800HT Pipe Fittings Specifications

Product Name:	Incoloy 800 Pipe Fittings \| Incoloy 800H Pipe Fittings \| Incoloy 800HT Pipe Fittings
Specifications:	ASTM B366 / ASME SB366
size:	Welded Butt Weld Fittings:1/2″ – 48″ Seamless Butt Weld Fittings: 1/2″ – 10″ in Sch 10s, 40s, 80s, 160s, XXS. (DN6~DN100)
Dimensions:	ASME/ANSI B16.9, MSS-SP-43, ASME B16.28, BS1560, BS4504, BS4504, BS10
Types:	Seamless / Welded / Fabricated
Thickness:	SCH 10, SCH 20, SCH 30, SCH 40, SCH 60, SCH 80, SCH 100, SCH 120, SCH 140, SCH 160, XS, XXS available with NACE MR 01-75
Bending Radius:	R=1D, 2D, 3D, 5D, 6D, 8D, 10D or Custom MSS Sp-43 Incoloy Alloy Steel Pipe Fitting
Elbows:	Angle: 22.5 deg, 30 deg, 45 deg, 90 deg, 180 deg, 1D, 1.5D, 2D, 2.5D, 3D, 4D, 5D, 6D, 7D, 8D, 10D-40D. Standard: ASME B16.9, ASME B16.25, ASME B16.28, MSS SP-75 JISB2311 JISB2312 JISB2313, DIN2605 GB, BS, ISO
Manufacturing process:	Forge, Cast, Push, Press, etc.
Key markets and industries:	Bitumen upgraders. Petrochemicals and acids. Heavy oil refineries. Nuclear power (largely seamless).
Test Certificates (TC):	Raw Materials Certificate, EN 10204/3.1B, 100% Radiography Test Report, Third Party Inspection Report, etc
Material Test Certificates (MTC):	As per EN 10204 3.1 and EN 10204 3.2, TC certifying NACE MR0103, NACE MR0175
Uses & Application:	Fittings To Connect Pipe & Tubes in Petroleum, Chemical, Power, Gas, Construction, Metallurgy, Shipbuilding. Schedule 10 fittings are an economical alternative for lower-pressure applications. Schedule 40 fittings have a thicker wall for higher-pressure applications.

ASTM B366 UNS N08800 Buttweld Fittings Equivalent Grades

STANDARD	WERKSTOFF NR.	UNS	JIS	BS	GOST	AFNOR	EN	OR
Incoloy 800	1.4876	N08800	NCF 800	NA 15	ЭИ670	Z8NC32-21	X10NiCrAlTi32-20	XH32T
Incoloy 800H	1.4958 / 1.4876	N08810	NCF 800H	NA 15(H)	ЭИ670	Z8NC33-21	X5NiCrAlTi31-20	XH32T
Incoloy 800HT	1.4859 / 1.4876	N08811	NCF 800HT	NA 15(HT)	ЭИ670	–	X8NiCrAlTi32-21	XH32T

Incoloy Alloy 800/800H/800HT Pipe Fittings Chemical Composition

Grade	C	Mn	Si	S	Cu	Fe	Ni	Cr	Al	Ti
800	0.10 max	1.50 max	1.00 max	0.015 max	0.75 max	39.50 min	30.00 – 35.00	19.00 – 23.00	0.15 – 0.60	0.15 – 0.60
800H	0.05 – 0.10	1.50 max	1.00 max	0.015 max	0.75 max	39.50 min	30.00 – 35.00	19.00 – 23.00	0.15 – 0.60	0.15 – 0.60
800HT	0.06 – 0.10	1.50 max	1.00 max	0.015 max	0.75 max	39.50 min	30.00 – 35.00	19.00 – 23.00	0.15 – 0.60ᴬ	0.15 – 0.60ᴬ

Incoloy 800/800H/800HT Pipe Fittings Mechanical Properties

Element	Density	Melting Point	Tensile Strength	Yield Strength (0.2%Offset)	Elongation
800 / 800H / 800HT	7.94 g/cm3	1385 °C (2525 °F)	Psi – 75,000 , MPa – 520	Psi – 30,000 , MPa – 205	30 %

Nickel Alloy 800 Pipe Fittings Size Range

Below Mentioned Pipe Fitting Size: 1/2″ – 48″
ASTM B366 Incoloy 800 Elbow – Long Radius	Incoloy 800 ASTM B366 Stub Ends
Incoloy 800 Elbow – Short Radius	ASTM B366 Incoloy Alloy 800 Cross
ASTM B366 Incoloy 800 Reducing Elbow	ASTM B366 Incoloy 800 Reducing Cross
ASTM B366 Incoloy 800 45° Elbow	ASTM B366 Incoloy 800 Tees
ASTM B366 Incoloy 800 Fabricated Tee	ASTM B366 Incoloy 800 End Cap
ASTM B366 Incoloy 800 Reducer	ASTM B366 Incoloy 800 Coupling
ASTM B366 Incoloy 800 Concentric Reducer	ASTM B366 Incoloy 800 Pipe Nipple
ASTM B366 Incoloy 800 Eccentric Reducer	ASTM B366 Incoloy 800 5D Elbow
ASTM B366 Incoloy 800 3D Elbow	ASTM B366 Incoloy 800 Welded Pipe Fittings

Incoloy 800 Buttweld Fittings Standards

American Steel Pipe Fittings Standard
Standard Code	Standard Name
Forged Durimet pipe fittings	ANSI ASME SA-366
Factory-Made wrought steel pipe fittings	ANSI ASME B16.9
Wrought steel butt-welding short radius elbows and returns	ANSI ASME B16.28
Incoloy butt-welding fittings	ISO 5251
Wrought Incoloy butt-welding fittings	MSS SP-43
Forging butt-welding fittings	MSS SP-75
Japanese Steel Pipe Fittings Standard
Universal steel butt-welding pipe fittings	JIS B2311
Steel butt-welding pipe fittings	JIS B2312
Steel plate butt-welding pipe fittings	JIS B2313
German Steel Pipe Fittings Standard
Steel butt-welding pipe fittings.elbows and bends	DIN 2605
Steel butt-welding pipe fittings.tees	DIN 2615
Steel butt-welding pipe fittings.reducers	DIN 2616
Steel butt-welding pipe fittings.caps	DIN 2617
Other Steel Pipe Fittings Standard
3 Butt-welding pipe fittings	EN 1025

Inconel Alloy 800 Buttweld Pipe Fittings Dimensional Tolerances

Tolerance of Butt-welding Fittings ASME B16.9


All Fittings[Note(1) and (2)]				Center-to-End Diamensions		Overall Length of Reducers and Lap Joint Stub Ends,F,H	Overall Length of Caps, E	180-deg Returns
Nominal Pipe Size(NPS)	DN	Outside Diameter at Bevel,D[Note(3) and (4)]	Inside Diameter at End [Note(3) and (5)]	90-deg and 45-deg Long and Short Radius Elbows and Tees. A,B,C,M	3D Radius Elbows, A,B	Overall Length of Reducers and Lap Joint Stub Ends,F,H	Overall Length of Caps, E	Center-to-Center Dimension, O	Back-to-Face Demensoin, K	Alignment of Ends, U
1/2to2 1/2	15-65	+1.6-0.8	0.8	2	3	2	3	6	6	1
3to3 1/2	80-90	1.6	1.6	2	3	2	3	6	6	1
4	100	1.6	1.6	2	3	2	3	6	6	1
5to8	125-200	+2.4 -1.6	1.6	2	3	2	6	6	6	1
10to18	250-450	+4.0 -3.2	3.2	2	3	2	6	10	6	2
20to24	500-800	+6.4 -4.8	4.8	2	3	2	6	10	6	2
26to30	650-750	+6.4 -4.8	4.8	3	6	5	10	…	…	…
32to48	800-1200	+6.4 -4.8	4.8	5	6	5	10	…	…	…
All Fittings[Note(1) and (2)]				Center-to-End Diamensions			Nominal Pipe Size(NPS)	DN	Angularity Tolerance
Nominal Pipe Size(NPS)	DN	Outside Diameter at Bevel,D[Note(3) and (4)]	Inside Diameter at End [Note(3) and (5)]	Outside Diameter of Lap,G	Fillet Radius of Lap,R	Lap Thickness	Nominal Pipe Size(NPS)	DN	Off Angle,Q	Off Plane,P
1/2to2 1/2	15-65	+1.6-0.8	0.8	+0,-1	+0,-1	+1.6,-0	1/2to4	15-100	1	2
3to3 1/2	80-90	1.6	1.6	+0,-1	+0,-1	+1.6,-0	5to8	125-200	2	4
4	100	1.6	1.6	+0,-1	+0,-2	+1.6,-0	10to12	250-300	3	5
5to8	125-200	+2.4 -1.6	1.6	+0,-1	+0,-2	+1.6,-0	14to16	350-400	3	6
10to18	250-450	+4.0 -3.2	3.2	+0,-2	+0,-2	+3.2,-0	18to24	450-800	4	`10
20to24	500-800	+6.4 -4.8	4.8	+0,-2	+0,-2	+3.2,-0	26to30	650-750	5	10
26to30	650-750	+6.4 -4.8	4.8	…	…	…	32to42	800-1050	5	13
32to48	800-1200	+6.4 -4.8	4.8	…	…	…	44to48	1100-1200	5	19

GENERAL NOTES:
(a)All dimensions are in mm.
(b)Tolerances are equal plus and minus except as noted.

NOTES:
(1)The inside diameter and the nominal wall thicknesat ends are to be specified by the purchaser.
(2)A minimum wall thickness of 87.5% applies unless the purchaser specifies a different wall thickness toletance.
(3)Out-of-round is the sum of absolute values of plus and minus tolerances.

Incoloy 800 Buttweld Fittings Dimensions

Dimensions and weights of ASME B16.9 Incoloy 800 Buttweld 45 Degree Elbow, 90 Degree Elbows Short and Long Radius (NPS 1/2 to 24, schedule STD/XS)

Pipe Elbow Nominal Size		Pipe Elbow Outside Diameter Y	Wall Thickness T (Pipe Elbow Schedule)		45 Deg. Elbow LR Centre to Face B	45 Deg. Elbow LR Weight	90 Deg. Elbow LR Centre to Face A	90 Deg. Elbow LR Weight	90 Deg. Elbow SR Centre to Face A	90 Deg. Elbow SR Weight
mm	in	mm	mm	Schedule	mm	kg	mm	kg	mm	kg
15	1/2”	21.3	2.78	STD	15.9	0.04	38.1	0.08	–	–
			3.73	X.S	15.9	0.05	38.1	0.10	–	–
20	3/4”	26.7	2.87	STD	11.1	0.04	28.6	0.08	–	–
			3.91	X.S	11.1	0.05	28.6	0.11	–	–
25	1”	33.4	3.38	STD	22.2	0.09	38.1	0.15	25.4	0.11
			4.55	X.S	22.2	0.11	38.1	0.19	25.4	0.14
32	11/4”	42.2	3.56	STD	25.4	0.14	47.6	0.28	31.75	0.18
			4.85	X.S	25.4	0.2	47.6	0.39	31.75	0.24
40	11/2”	48.3	3.68	STD	28.6	0.2	57.1	0.4	38.1	0.26
			5.08	X.S	28.6	0.25	57.1	0.5	38.1	0.35
50	2”	60.3	3.91	STD	34.9	0.36	76.2	0.72	50.8	0.5
			5.54	X.S	34.9	0.5	76.2	1.0	50.8	0.68
65	21/2”	73.0	5.16	STD	44.4	0.73	95.2	1.46	63.5	0.95
			7.01	X.S	44.4	0.91	95.2	1.82	63.5	1.27
80	3”	88.9	5.49	STD	50.8	1.1	114.3	2.18	76.2	1.45
			7.62	X.S	50.8	1.45	114.3	2.86	76.2	1.95
100	4”	114.3	6.02	STD	63.5	2.1	152.4	4.2	101.6	2.8
			8.56	X.S	63.5	2.9	152.4	5.7	101.6	3.9
125	5”	141.3	6.65	STD	79.4	3.4	190.0	6.8	127.0	4.8
			9.5	X.S	79.4	5.0	190.0	10.0	127.0	6.5
150	6”	168.3	7.11	STD	95.2	5.1	229.0	10.1	152.4	6.8
			10.97	X.S	95.2	7.7	229.0	15.3	152.4	10.2
200	8”	219.1	8.18	STD	127.0	10.2	305.0	20.4	203.0	13.6
			12.7	X.S	127.0	15.5	305.0	30.9	203.0	20.9
250	10”	273.9	9.27	STD	159.0	18.1	381.0	36.1	254.0	24.1
			12.7	X.S	159.0	24.4	381.0	48.8	254.0	32.5
300	12”	323.9	9.52	STD	190.0	26.6	457.0	53.1	305.0	35.4
			12.7	X.S	190.0	35.0	457.0	70.0	305.0	46.7
350	14”	355.6	9.52	STD	222.0	34.1	533.0	68.1	356.0	45.4
			12.7	X.S	222.0	45.0	533.0	90.0	356.0	60.0
400	16”	406.4	9.52	STD	254.0	45.0	610.0	89.3	406.0	59.5
			12.7	X.S	254.0	59.0	610.0	118.0	406.0	78.7
450	18”	457.0	9.52	STD	286.0	56.5	686.0	113.0	457.0	75.6
			12.7	X.S	286.0	75.0	686.0	150.0	457.0	100.0
500	20”	508.0	9.52	STD	318.0	85.0	762.0	140.0	508.0	93.5
			12.7	X.S	318.0	112.5	762.0	186.0	508.0	124.0
800	24”	610.00	9.52	STD	381.0	101.5	914.0	203.0	610.0	135.0
			12.7	X.S	381.0	134.5	914.0	269.0	610.0	179.0

Dimensions and weights of ASME B16.9 Incoloy 800 Buttweld Tee and Cap (NPS 1/2 to 24, schedule STD/XS)

Buttweld Tee and Cap Nominal Size		Pipe Tee and Cap Outside Diameter Y	Pipe Tee and Cap Wall Thickness T		Buttweld Tee Dimensions (C and M)	Buttweld Tee Weight	Buttweld Cap End to End	Buttweld Cap Weight
mm	in	mm	mm	Schedule	mm	mm	mm	kg
15	1/2”	21.3	2.78	STD	25.4	0.58
			3.73	X.S	25.4	0.21
20	3/4”	26.7	2.87	STD	28.6	0.21
			3.91	X.S	28.6	0.27
25	1”	33.4	3.38	STD	38.1	0.34	38.1	0.1
			4.55	X.S	38.1	0.43	38.1	0.14
32	11/4”	42.2	3.56	STD	47.6	0.64	38.1	0.14
			4.85	X.S	47.6	0.75	38.1	0.18
40	11/2”	48.3	3.68	STD	57.1	0.95	38.1	0.18
			5.08	X.S	57.1	1.13	38.1	0.23
50	2”	60.3	3.91	STD	63.5	1.45	38.1	0.27
			5.54	X.S	63.5	1.72	38.1	0.32
65	21/2”	73.0	5.16	STD	76.2	2.45	38.1	0.41
			7.01	X.S	76.2	2.95	38.1	0.45
80	3”	88.9	5.49	STD	85.7	3.45	50.8	0.64
			7.62	X.S	85.7	4.3	50.8	0.82
100	4”	114.3	6.02	STD	105.0	5.7	63.5	1.13
			8.56	X.S	105.0	7.3	63.5	1.54
125	5”	141.3	6.65	STD	124.0	9.1	76.2	1.91
			9.5	X.S	124.0	11.8	76.2	2.59
150	6”	168.3	7.11	STD	143.0	13.6	88.9	2.95
			10.97	X.S	143.0	19.0	88.9	4.1
200	8”	219.1	8.18	STD	178.0	25.0	101.6	5.0
			12.7	X.S	178.0	33.5	101.6	7.3
250	10”	273.0	9.27	STD	216.0	41.0	127.0	9.1
			12.7	X.S	216.0	54.0	127.0	12.0
300	12”	323.9	9.52	STD	254.0	57.0	152.4	13.6
			12.7	X.S	254.0	77.0	152.4	17.0
350	14”	355.6	9.52	STD	279.0	73.0	165.1	15.9
			12.7	X.S	279.0	93.0	165.1	21.0
400	16”	406.4	9.52	STD	305.0	91.0	178.8	20.0
			12.7	X.S	305.0	120.0	178.8	26.0
450	18”	457.0	9.52	STD	343.0	127.0	203.2	26.0
			12.7	X.S	343.0	165.0	203.2	34.0
500	20”	508.0	9.52	STD	381.0	227.0	228.6	33.0
			12.7	X.S	381.0	270.0	228.6	43.0
800	24”	610.0	9.52	STD	432.0	345.0	266.7	46.0
			12.7	X.S	432.0	430.0	266.7	61.0

Dimensions and Weights of ASME B16.9 Incoloy 800 Buttweld Concentric Reducers and Eccentric Reducers(NPS 1/2 to 24, schedule STD/XS)

Buttweld Reducer Nominal Size		Pipe Reducer Length H	Pipe Reducer Schedule T	Pipe Reducer Weight
mm	in	mm		Kg
20×15	3/4” x 1/2”	38.1	STD	0.07
			XS	0.1
25×15	1” x 1/2”	50.8	STD	0.14
			X.S	0.18
25×20	1” x 3/4”	50.8	STD	0.14
			X.S	0.18
32×15	11/4” x 1/2”	50.8	STD	0.18
			X.S	0.23
32×20	11/4” x 3/4“	50.8	STD	0.18
			X.S	0.23
32×25	11/4” x 1”	50.8	STD	0.18
			X.S	0.23
40×15	11/2” x 1/2”	63.5	STD	0.27
			X.S	0.32
40×20	11/2” x 3/4”	63.5	STD	0.27
			X.S	0.32
40×25	11/2” x 1”	63.5	STD	0.27
			X.S	0.32
40×32	11/2” x 11/4”	63.5	STD	0.27
			X.S	0.32
50×15	2” x 1/2”	76.2	STD	0.41
			X.S	0.54
50×20	2” x 3/4”	76.2	STD	0.41
			X.S	0.54
50×25	2”x1”	76.2	STD	0.41
			X.S	0.54
50×32	2” x 11/4”	76.2	STD	0.41
			X.S	0.54
50×40	2” x 11/2”	76.2	STD	0.41
			X.S	0.54
65×25	21/2” x 1”	88.9	STD	0.68
			X.S	0.91
65×32	21/2” x 11/4”	88.9	STD	0.68
			X.S	0.91
65×40	21/2” x 11/2”	88.9	STD	0.68
			X.S	0.91
65×50	21/2” x 2”	88.9	STD	0.68
			X.S	0.91
80×40	3” x 11/2”	88.9	STD	0.77
			X.S	1.09
80×50	3”x2”	88.9	STD	0.91
			X.S	1.22
80×65	3” x 21/2”	88.9	STD	0.91
			X.S	1.27
100×40	4” x 11/2”	101.6	STD	1.36
			X.S	1.91
100×50	4”x2”	101.6	STD	1.40
			X.S	1.95
100×65	4” x 21/2”	101.6	STD	1.45
			X.S	2.04
100×80	4”x3”	101.6	STD	1.59
			X.S	2.08
125×80	5”x3”	127.0	STD	2.5
			X.S	3.4
125 x 100	5”x4”	127.0	STD	2.7
			X.S	3.8
150×50	6”x2”	140.0	STD	3.4
			X.S	4.3
150×65	6” x 21/2”	140.0	STD	3.4
			X.S	4.5
150×80	6”x3”	140.0	STD	3.6
			X.S	4.8
150 x 100	6”x4”	140.0	STD	3.7
			X.S	5.2
150 x 125	6”x5”	140.0	STD	3.9
			X.S	5.4
200×80	8”x3”	152.4	STD	4.5
			X.S	7.2
200 x 100	8”x4”	152.4	STD	5.0
			X.S	7.7
200 x 125	8”x5”	152.4	STD	5.4
			X.S	8.2
200 x 150	8”x6”	152.4	STD	5.9
			X.S	8.6
250 x 100	10”x4”	178.0	STD	9.1
			X.S	11.8
250 x 125	10”x5”	178.0	STD	9.5
			X.S	13.6
250 x 150	10”x6”	178.0	STD	9.5
			X.S	13.6
250 x 200	10”x8”	178.0	STD	10.0
			X.S	14.0
300 x 150	12”x6”	203.0	STD	14.1
			X.S	18.1
300 x 200	12”x8”	203.0	STD	14.5
			X.S	19.1
300 x 250	12” x 10”	203.0	STD	15.4
			X.S	20.0
350 x 200	14”x8”	330.0	STD	26.3
			X.S	34.9
350 x 250	14” x 10”	330.0	STD	27.2
			X.S	36.3
350 x 300	14” x 12”	330.0	STD	28.6
			X.S	37.6
400 x 200	16”x8”	356.0	STD	31.8
			X.S	42.6
400 x 250	16” x 10”	356.0	STD	33.1
			X.S	43.5
400 x 300	16” x 12”	356.0	STD	34.5
			X.S	45.4
400 x 350	16” x 14”	356.0	STD	35.4
			X.S	46.3
450 x 250	18” x 10”	381.0	STD	38.0
			X.S	52.1
450 x 300	18” x 12”	381.0	STD	39.0
			X.S	53.5
450 x 350	18” x 14”	381.0	STD	40.0
			X.S	54.9
450 x 400	18” x 16”	381.0	STD	40.8
			X.S	53.5
500 x 250	20” x 10”	508.0	STD	53.0
			X.S	79.9
500 x 300	20” x 12”	508.0	STD	54.4
			X.S	82.0
500 x 350	20” x 14”	508.0	STD	57.6
			X.S	80.2
500 x 400	20” x 16”	508.0	STD	58.9
			X.S	82.0
500 x 450	20” x 18”	508.0	STD	61.7
			X.S	82.0
800 x 300	24” x 12”	508.0	STD	63.5
			X.S	84.4
800 x 350	24” x 14”	508.0	STD	65.3
			X.S	86.8
800 x 400	24” x 16”	508.0	STD	68.0
			X.S	90.4
800 x 450	24” x 18”	508.0	STD	72.6
			X.S	96.5
800 x 500	24” x 20”	508.0	STD	77.1
			X.S	102.5

Incoloy 800 Buttweld Fittings Types

Note: Prices are based on product, material grade and quantity. Contact us anytime to get full quotation.

GET UPDATED PRICE AND COMPLETE QUOTATION WITHIN AN HOUR sales@metalfed.com

ASTM B366 Incoloy 800 Buttweld Pipe Fittings – Applications & Industries

Oil & Gas Industries

Gas Processing Industries

Food Processing Industries

Petrochemical Industries

Chemical Industries

Power Generation Industries

Sugar Industries

Fertilizers Industries

We are well-known prestigious Manufacturers, Exporters, and Suppliers of high quality Incoloy Alloy 800 Buttweld Pipe Fittings. We supply ANSI B16.9 Incoloy 800 Pipe Fittings to customers in various industries including chemical, pharmaceutical, petrochemical, power, engineering and various other industrial applications. Test Certificate as per EN 10204 / 3.1B, Raw Materials Certificate, Third Party Inspection Report and 100% Radiography Test Report.

Ready Stock of Incoloy 800/800H/800HT Pipe Fittings Export to

Africa Algeria, Angola, Benin, Botswana, Burkina Faso, Burundi, Cabo Verde, Cameroon, Central African Republic (CAR), Chad, Comoros, The Democratic Republic of the Congo, Republic of the Congo, Cote d’Ivoire, Djibouti, Egypt, Equatorial Guinea, Eritrea, Ethiopia, Gabon, Gambia, Ghana, Guinea, Guinea-Bissau, Kenya, Lesotho, Liberia, Libya, Madagascar, Malawi, Mali, Mauritania, Mauritius, Morocco, Mozambique, Namibia, Niger, Nigeria, Rwanda, Sao Tome and Principe, Senegal, Seychelles, Sierra Leone, Somalia, South Africa, South Sudan, Sudan, Swaziland, Tanzania, Togo, Tunisia, Uganda, Zambia, Zimbabwe

Europe,Albania, Finland, France, Ireland, Italy, Andorra, Armenia, Austria, Bosnia and Herzegovina, Bulgaria, Croatia, Cyprus, Czech Republic, Georgia, Germany, Denmark, Estonia, Kazakhstan, Kosovo, Greece, Hungary, Iceland, Latvia, Liechtenstein, Azerbaijan, Belarus, Belgium, Lithuania, Luxembourg, Macedonia, Malta, Moldova, Monaco, Montenegro, Netherlands, Norway, Poland, Portugal, Romania, Russia, San Marino, Serbia, Slovakia, Slovenia, Spain, Sweden, Turkey, Ukraine, United Kingdom, Vatican City

AmericaAntigua and Barbuda, Bahamas, Barbados, Belize, Canada, Costa Rica, Cuba, Dominica, Dominican Republic, El Salvador, Grenada, Guatemala, Haiti, Honduras, Jamaica, Mexico, Nicaragua, Panama, Saint Kitts and Nevis, Saint Lucia, Saint Vincent and the Grenadines, Trinidad and Tobago, United States of America, Argentina, Bolivia, Brazil, Chile, Colombia, Ecuador, Guyana, Paraguay, Peru, Suriname, Uruguay, Venezuela

Asia/OceaniaAfghanistan, Armenia, Azerbaijan, Bahrain, Bangladesh, Bhutan, Brunei, Cambodia, China, Cyprus, Georgia, India, Indonesia, Iran, Iraq, Israel, Japan, Jordan, Laos, Lebanon, Malaysia, Maldives, Mongolia, Myanmar (Burma), Oman, Pakistan, Palestine, Philippines, Qatar, Nepal, North Korea, Russia, Saudi Arabia, Singapore, South Korea, Sri Lanka, Syria, Taiwan, Tajikistan, Thailand, Timor-Leste, Turkey, Turkmenistan, United Arab Emirates (UAE), Uzbekistan, Vietnam, Yemen, Australia, Fiji, Kiribati, Marshall Islands, Micronesia, Nauru, New Zealand, Palau, Papua New Guinea, Samoa, Solomon Islands, Tonga, Tuvalu, Vanuatu

CONTACT

Please send us the complete details of Incoloy Alloy 800H Pipe Fittings requirement. We offer Alloy 800HT Pipe Fittings which are accurately designed to provide satisfaction to our customers. We have huge ready stock of Incoloy 800 Buttweld Elbow, Incoloy 800H Tee, Reducer, Bend, Cross, End Caps, Stub Ends, Coller, Pipe Nipple at our valuable customers end. Buy ASTM B366 Incoloy 800HT Pipe Fittingat a lowest price from us.

sales@metalfed.com | +91 9137898594 | Quotation Form | Reach Us